Right here in the next paragraph you might get a good deal of good content around How to Install a Bathtub Yourself.
Mounting a bath tub isn't exactly rocket science, but it does call for solid plumbing, woodworking, and also in some cases, tiling abilities. Replacing an old bathtub with a new one is likewise a reasonably hard project. If the old tub is conveniently accessible, the task can move rapidly; if you have to open a wall surface to get rid of the old bathtub and also place the brand-new bathtub, the task is a lot harder. In either situation, the task is within a home handyman's abilities, although you will require a helper to leave the old tub as well as embeded in the new one. Make certain you have certified yourself for the task and also fit attempting it. Instead of working with a service provider to take control of a halfway-completed task, it is far better to take into consideration employing one before you begin. Chances are you may need a professional plumber to make tube connections.
This short article will help you set up a new bathtub in your bathroom if you have already purchased a new tub and do not require to transform the plan of your previous water system pipes.
Your tools as well as material list need to make up the following:
Planning for the Setup
Firstly, the sustaining framework supplied with the bath needs to be fitted (if needed) according to the maker's directions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is essential to make sure that if the faucet includes a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the taps unit to stop strain on the bathtub.
Fit the adaptable faucet ports to the bottom of both faucets utilizing 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet via the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you use all of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bath must currently prepare to be fitted in its last placement.
Removing Old Touches
If you need to change old taps with new ones as a part of your setup, after that the first thing you ought to do is separate the supply of water. After doing so, activate the taps to drain pipes any kind of water remaining in the system. The procedure of removing the existing faucets can be fairly problematic as a result of the restricted accessibility that is typically the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the taps. Have a towel ready for the remaining water that will originate from the pipelines. As soon as the supply pipes have been eliminated, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary taps from turning during this process. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old sealing substance.
Prior to moving on to fit the new taps, compare the pipeline links on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bathtub
Using the two wooden boards under its feet, put the bath tub in the called for placement. The wooden boards are useful in uniformly spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto four little points.
The next goal is to guarantee that the bathtub is leveled all round. This can be attained by examining the level and also readjusting the feet on the tub up until the level checks out degree.
To set up taps, fit the bottom of the outermost versatile faucet port to the proper supply pipe by making a compression join; after that do the very same for the various other faucet.
Turn on the supply of water and examine all joints and also brand-new pipework for leakages and also tighten them if essential. Load the tub and also check the overflow electrical outlet and also the typical outlet for leaks.
Lastly, repair the bathroom paneling as explained in the producer's instruction manual. Tiling and also securing around the tub ought to wait till the tub has been made use of a minimum of once as this will certainly settle it right into its last setting.
Fitting New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic adapter to avoid damages to the string. One end of the connector fits on the plastic tail of the faucet as well as the other end gives a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin ensuring that the washers remain in place between the tap as well as the sink. Safeguard the tap in position with the manufacturer offered backnut. When the faucet is safely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with regular faucet connectors. The former kind needs to be attached to the tap finishes first, tightening up just by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bathroom meets the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is essential as the installation can move enough to fracture a rigid seal, triggering the water to pass through the wall between the bathroom and the tiling, resulting in issues with wetness and possible leakages to the ceiling listed below.
You can select from a variety of coloured sealants to assimilate your fixtures as well as installations. They are offered in tubes and also cartridges, and can securing gaps as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of soaked paper or soft rope. Remember to always fill up the bath tub with water before securing, to permit the movement experienced when the tub remains in usage. The sealant can split rather early if you do not take into account this motion prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly offered on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or water resistant glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I found that post on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround while doing a search on the internet. Sharing is good. You just don't know, you may very well be helping someone out. Thank you for taking the time to read it.
Set An Appointment